Veteran Garage Door Repair | Keller TX | 817-769-8488

Veteran Garage Door Repair | Keller TX | 817-769-8488

Garage Door Opener Repair

You may discover that your garage door opener has actually been providing you problems, so you need to fix it. You can fix it by changing a circuit board, a photo-eye sensing unit, the major drive equipment, or the set-limit switches. You can also inspect if the safety and security sensing units are functioning properly.

Replacing a circuit card

Replacing a motherboard for your garage door opener needs a few steps as well as devices. Initially, you require to switch off the breaker as well as disconnect any wires. Next off, open up the circuit card cover. This will assist you to diagnose the problem and also figure out if you require a new board. Next, get rid of the old board as well as its cord adapters.

You can after that continue to replace the circuit board. The replacement procedure is easy and also takes around 10 mins. A new circuit card will set you back about $80. To protect your new circuit card from power rises, you can acquire a surge guard.

Changing a photo-eye sensing unit

Replacing a photo-eye sensing unit can be a rather straightforward task. First, remove the sensor from the door and also make sure it is located correctly. If the sensing unit is angled in any way, it may not be getting the proper signal, which might be creating the blinking lights. If you discover that the photo-eyes are out of alignment, you may require to have actually a service technician come as well as deal with the problem.

The photo-eye sensing unit includes 2 pieces that place outside of the door tracks as well as toward the flooring. The image eyes will certainly have a small LED light and also must be solid in color. If the light is blinking, its most likely the photo-eye is defective and will certainly need to be replaced.

Changing a main drive equipment

To change a garage door opener primary drive equipment, start by eliminating the cap from the chain pulley. Next off, remove both screws holding the drive equipment to the gear setting up. Currently, you can loosen the 3 tension pins. Squeeze them from both sides and after that remove them. After that, detach the three wires from the garage door opener electric motor. These wires should be white, red, and also blue.

When you have eliminated the old gear, set up a brand-new one. Make certain to oil it well. Put the brand-new equipment into the shaft, seeing to it to align the mounting holes. See to it the gear and sprocket assembly are located properly to make certain smooth operation. Next, make use of a hammer and also a nail to drive a pin right into the new gear.

Changing the set-limit switches

The very first point you should do if your garage door is not working properly is to examine the set-limit buttons. You may require to change them to ensure that the door shuts earlier or quits before it reaches the flooring. You can examine this by considering your garage doors handbook or online.

To readjust the set-limit switches, youll require a screwdriver or socket. Readjust the knob clockwise or counterclockwise up until the door goes up as well as stops, or lowers its distance. To check for correct travel range, measure the void from all-time low of the garage door to the ground.

Veteran Garage Door Repair – Keller

204 S Main St Ste 105, Keller, TX 76248, USA

817-769-8488

https://veterangaragedoor.com/veteran-garage-door-repair-of-keller-tx/


Garage Door Repair


Garage Door Installation


Garage Door Company


Garage Door Service


Garage Door Opener Repair

Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488
Veteran Garage Door Repair

204 S Main St Ste 105
Keller,TX
76248
817-769-8488

Leave a Reply

Your email address will not be published. Required fields are marked *


Back To Top